Honda City (GM6) Cat Pipe

The direct replacement SUPERCIRCUIT cat pipe designed for the 6th generation Honda City (GM6) is installed and tested for performance. This cat pipe is to replace the secondary catalytic converter to lessen the restriction and hence better exhaust flow efficiency and higher output. This cat pipe is ideal for track or race use.

Here are the photos during the installation:

There are two catalytic converters on the stock exhaust system of the Sixth generation Honda City GM6, one on the exhaust header/ extractor and the other one is at the cat pipe (or some called it the b-pipe).

The SUPERCIRCUIT cat pipe is made of grade 304 stainless steel mandrel bent 2.0" pipe and fully TIG/Argon welded on laser cut stainless steel flange for optimum flow efficiency yet not over done it to cause the lost of 'back pressure'. 

Below picture, the Honda City GM6 stock factory cat pipe with a big catalytic converter vs. the SUPERCIRCUIT  cat pipe which is catless.

The SUPERCIRCUIT cat pipe is designed to bolt-on and replacing the stock original straight away, no cut or weld is required.

To purchase or for information about the above 6th Generation Honda City  GM6 cat pipe, please visit us at SuperCircuit exhaust Pro Shop, SS13 Subang Jaya Industrial Estate. Tel: 03 5632 2855 or Send Us A Message using the form on the right of this page.

Please join SuperCircuit Exhaust Facebook for more exhaust news and updates.

Honda Civic FB 2.0 Headers

Following the custom made Honda Civic FB 1.8 cat-back exhaust system earlier this week, here is another Honda Civic FB 2.0 at SuperCircuit Exhaust Pro Shop for the SUPERCIRCUIT headers.

The SUPERCIRCUIT Headers/ Extractors made for the Honda Civic FB 2.0 is designed to bolt-on straight away, no further modification is required.

The SUPERCIRCUIT headers installed to the Ninth Generation Honda Civic (code name Civic FB) with the R20A engine is shown below. 

The SUPERCIRCUIT Headers/ Exhaust Extractors for the 9th generation Honda Civic FB R20A engine is made of grade 304 stainless steel mandrel bent pipes and fully TIG/Argon hand welded by the master craftsmen here at the SUPERCIRCUIT Exhaust Pro Shop.

Beside the polished mandrel bent stainless steel pipes, the flanges are all made from laser cut stainless steel material for perfect fitting and durability. The headers do not just looking good, it helps to gain more horsepower and torque too!

Closeup look of the SUPERCIRCUIT stainless steel EGR flange vs. the Honda Civic FB factory stock header's EGR flange made of mild steel (SEE BELOW).

To purchase or for information about the above 9th Generation Honda Civic FB 2.0 Extractors, please visit us at SuperCircuit exhaust Pro Shop, SS13 Subang Jaya Industrial Estate. Tel: 03 5632 2855 or Send Us A Message using the form on the right of this page.

Please join SuperCircuit Exhaust Facebook for more exhaust news and updates.

Honda Civic FB 1.8 Catback Exhaust System

When it comes to exhaust customization, SUPERCIRCUIT Exhaust Pro Shop always one of the top picks if you are from this part of the Peninsular.

Here is a good example of the custom made catback exhaust system of the Honda Civic FB 1.8 by SUPERCIRCUIT Exhaust Pro Shop.

The Honda Civic FB 1.8 catback exhaust system is customized with grade 304 stainless steel mandrel bent pipes and fully TIG/Argon welded for optimum performance and durability.

The S-flow muffler of the Honda Civic FB 1.8 rear section shown below.

Full CNC mandrel bent pipes and a centre resonator forms the mid-section of the Honda Civic FB 1.8 exhaust setup.

For top notched craftsmanship and a quality exhaust customization job, please contact SUPERCIRCUIT Exhaust Pro Shop. Tel: +6 03 5632 2855 or Send Us A Message using the form on the right of this page.

Please join SuperCircuit Exhaust Facebook for more exhaust news and updates. Thank you.

VW Golf 7 1.4TSI Downpipe

A set of good and restrict-less downpipe will help to gain more performance and for ease of tuning. Here is the SUPERCIRCUIT catless downpipe made for the VW Golf Mk7 1.4TSI:

The output of the Volkswagen Golf Mk7 1.4TSI BlueMotion turbo-charged engine is satisfyingly good, and we further improve it by a set of good restrict-less and larger bore downpipe from SUPERCIRCUIT.

The SUPERCIRCUIT catless downpipe is designed to bolt-on straight to the VW Golf mk7 1.4TSI turbo outlet, no modification required. (SEE BELOW)

At the other end of the SUPERCIRCUIT downpipe, there is a slip joint that is compatible with the factory stock exhaust system of the VW Golf 7 1.4TSI. It is just straight bolt-on!

The SUPERCIRCUIT downpipe is made with grade 304 stainless steel mandrel bent pipes and is fully TIG/Argon welded by the master craftsmen here at SUPERCIRCUIT. Installation is just straight bolt-on, no cut or weld is required.

To purchase or for information about the above catless downpipe made for the Volkswagen Golf Mk7 1.4TSI, please visit us at SuperCircuit exhaust Pro Shop, SS13 Subang Jaya Industrial Estate. Tel: 03 5632 2855 or Send Us A Message using the form on the right of this page.

Please join SuperCircuit Exhaust Facebook for more exhaust news and updates.

VW Scirocco 2.0 TSI Axle-back Exhaust Custom

When it comes to exhaust customization, SuperCircuit Exhaust Pro Shop is always one of the top choices if you are from this part of the Peninsular.

Exhaust customization will take slightly longer time because patience is needed to slowly craft and weld a beautiful piece of exhaust artwork and, most importantly, the car has to be here to get the job done.

The VW Scirocco 2.0 TSI axle-back exhaust system is custom made from grade 304 stainless steel mandrel bent pipes and fully TIG/Argon welded by the master craftsmen here at SuperCircuit Exhaust Pro Shop.

 Top notched craftsmanship matched with top quality material, this is SUPERCIRCUIT!

To custom made the VW Scirocco 2.0 TSI axle-back exhaust system constructed from high quality stainless steel mandrel bent pipes and quality mufflers, please visit us at SuperCircuit exhaust Pro Shop, SS13 Subang Jaya Industrial Estate. Tel: 03 5632 2855 or Send Us A Message using the form on the right of this page.

Please join SuperCircuit Exhaust Facebook for more exhaust news and updates.

Mazda 6 Axle-back Exhaust System

When it comes to custom made exhaust system, SuperCircuit Exhaust Pro Shop is always one of the top choices if you are living in the peninsular part of the country.

Here is the axle-back exhaust customized for the 3rd generation Mazda6 (GJ).

The twin muffler axle-back exhaust setup for the Mazda6 is hand crafted from 304 stainless steel mandrel bent pipes and fully TIG/Argon welded by the master craftsmen here at SuperCircuit Exhaust Pro Shop.

To make your beloved Mazda6 sounds and looks sportier, look no further for this custom made axle-back exhaust system by SuperCircuit Exhaust Pro Shop which is constructed with high quality stainless steel mandrel bent pipes and matched with a pair of quality stainless steel muffler boxes!

Please visit us at SuperCircuit exhaust Pro Shop, SS13 Subang Jaya Industrial Estate. Tel: 03 5632 2855 or Send Us A Message using the form on the right of this page.

Please join SuperCircuit Exhaust Facebook for more exhaust news and updates.

Honda Civic 1.8 FD Headers

The SUPERCIRCUIT catless Headers/ Extractors made for the Honda Civic FD 1.8 promotes better exhaust flow and lessen the restriction compared to the factory stock catalytic converter, hence better acceleration and top-end power. It is a must have item for those who would like to improve the performance of their Honda Civic FD 1.8!

The factory stock exhaust header of the Honda Civic FD 1.8 comes with a big catalytic converter (SEE BELOW).

We split the exhaust flow into two to get the effect of the conventional 4-2-1 extractor, this will free up restriction and minimize exhaust turbulence, in theory. It is further proven by dyno test during the R&D stage.

The SUPERCIRCUIT Honda Civic FD 1.8 Extractor/ Header is designed to bolt-on straight to the R18A mill, no further modification is required during the installation.

The Honda Civic FD 1.8 Exhaust Gas Recirculation (EGR) pipe has to be installed back to the pre-built EGR outlet of the SUPERCIRCUIT Headers, not a single thing is left out. (SEE BELOW)

The SUPERCIRCUIT Honda Civic 1.8 headers/ extractors is made with grade 304 stainless steel, then TiG/Argon welded on all stainless steel flanges for perfect fitting and optimized performance.

To purchase or for more information about the SUPERCIRCUIT Headers/ Extractor above, please visit us at SuperCircuit exhaust Pro Shop, SS13 Subang Jaya Industrial Estate. Tel: 03 5632 2855 or Send Us A Message using the form on the right of this page.

Please join SuperCircuit Exhaust Facebook for more exhaust news and updates

Mitsubishi ASX 2.0 Headers/ Extractor

The Mitsubishi ASX 2.0 is sharing the same headers/ extractor with the normal Mitsubishi Lancer 2.0 with the same 4B11 engine. The performance of the SUPERCIRCUIT's Lancer headers is proven on many Lancers all over the world. 

The SUPERCIRCUIT 4-2-1 Headers made for the Mitsubishi 4B11 Engine is designed to bolt-on straight with OEM compatible heat shield brackets, so the factory stock heat shield can be installed back in position.

The SUPERCIRCUIT Headers made for the Mitsubishi 4B11 2.0L engine is compatible with the rest of the stock exhaust system, just plug 'n play.

This headers is Made of grade 304 stainless steel and fully TIG/Argon welded by the master craftsmen here at SuperCircuit Exhaust Pro Shop.

To purchase or for more information about the SUPERCIRCUIT Headers/ Extractor above, please visit us at SuperCircuit exhaust Pro Shop, SS13 Subang Jaya Industrial Estate. Tel: 03 5632 2855 or Send Us A Message using the form on the right of this page.

Please join SuperCircuit Exhaust Facebook for more exhaust news and updates